 主要特点：
1. 该机广泛适用于30号(6.6mm)及以下水钻（两头尖实心）、一头尖实心钻（用于做平底钻）和两头尖空心珠的磨削和抛光工作。
2．超长夹具设计，有效针距达650mm,超多的夹具针,16号(3.8mm)钻针多达139枚，并且同时两只夹具一起工作，使产量大大提高。
3. 磨抛一体直线式设计，前边设有磨轮，后边设有抛轮，前边磨完成后自动移动至抛轮进行抛光，无需人工搬运夹具。
4.磨抛轮固定旋转，夹具升降采用高精度滚珠丝杆由步进电机带动，磨抛精度可精确到0.01mm，并且每个面可单独设置磨抛深度和时间，成品大小精确，最小可用于生产1mm即1号钻。
5. 控制系统采用先进的电脑PLC加液晶触摸屏，系统稳定可靠，参数设置调节方便。触摸屏全部显示中文，嵌套式菜单，易学易用，普通工人培训一天即可上岗。
6．系统具有抛轮磨损自动补偿功能，补偿周期和补偿值可任意设定，机器调好后操作工人仅需按启动按钮，无需再对参数进行调整。
7．机器机械结构及工作原理简单，因此稳定可靠，而且维护保养特别方便。
8．专门设计的故障排除功能，可从触摸屏上迅速判断输入输出信号是否正常，比如感应开关是否正常，按钮是否损坏等。
9．每班10小时可产16号（3.8mm）两头尖水钻20万颗以上。
Features:
1. This machine is suitable for grind & polish kinds of rhinestone and flat back rhinestone and hollow bead (hollow rhinestone) which it is smaller than SS30(6.6mm)。
2. Longer mould used, the distance of pin center reach 650mm, it has 139 pins for SS16 (3.8mm), and two mould work along at the same time, so it has high output.
3. Grind canister and polish canister are designed in a line, front is grind canister, behind is polish canister, the mould go to polish automatically after grind, needn’t replace the mould by hand.
4. The mould up-down system adopt high quality ball bearing pole, drive by step motor, and the up-down precision reach 0.01mm, also all side can set the parameter deepness and time alone, so the final product is exactitude. It can produce SS1 (1mm) at the smallest.
5. The control system adopt advanced PLC and touch screen, the system stability and reliability is high, the parameter set and adjust is convenience.
6. The system have polish canister abrasion expiation function, after machine adjust finished, the worker have nothing to but take the mould.
7. The machine structure and work principle are very good but very simple, so it is stably and easy to maintain.
8. Special designed trouble remove function, it can check if the input and output signal right or not from the touch screen conveniently. Such as judge the switch is right or not , the button is right or not, so remove the trouble quickly.
9. It can produce 200,000 SS16(3.8mm) rhinestone in ten hours.
主要参数Main Parameter:
1.主电机功率 Main motor 4KW
2.磨抛轮直径 Grind canister diameter φ280mm
3.夹具有效针距 Mould pin distance 650mm
4.外形尺寸 Dimension L2520*W1400*H1700
5.一组占地面积 One set Dimension L4800*W2800
6.重量 Weight： 2.0T
|
